Replacing the drain hose in the washing machine has some difficulties. We will tell you step by step how you can remove, change or clean the hose in any brand of SMA.
Some users think that replacing it is similar to a water inlet hose. However, it is not. The water intake hose is attached to the body of the washer, while the drain, in addition, is located next to the pump.
When drain hose replacement is required
The drain hose serves to drain the waste water, therefore it is attached to the drain pump, next to the nozzle. It is made of polypropylene, therefore it withstands water of different temperatures, and also remains resistant to chemicals.
For what reasons does he need a replacement?
- Inappropriate item. Often when you buy a washing machine in the kit, you get a hose. However, it may be short during installation. Of course, you can lengthen the element, but this increases the risk of water leakage.
- Mechanical damage. Replacing the drain hose of the washing machine may be necessary in the event of a fracture or leakage. It is recommended to replace the part immediately.
- The hose is clogged with scum so much that it needs to be replaced.
Right choice
Before replacing the drain hose, a suitable replacement must be selected. You have three options:
- The standard option. This is a classic, according to which the length of the part is from one to five meters. This is quite enough to connect the washer.
- Telescopic option. The name speaks for itself: a compressed hose measuring 0.5 meters stretches to a length of 1.5 meters. In addition to the advantages of mobility, there are also disadvantages. When stretched, large corrugated folds are formed, which vibrate strongly during operation.
- Bay option. Collapsible type, consists of modules measuring 50-55 centimeters. Convenient because you can adjust the length.
You do not know how to remove the drain hose from the washing machine? Lift the top panel and see where it is located. To do this, unscrew the two screws on the back and, sliding the panel in the opposite direction, remove.
For different models of SM, dismantling may vary, so consider the replacement in each of them.
Self-change drain hose
Next, we will tell you how to remove the drain hose from the washers of different manufacturers. You just have to choose your brand and proceed with the repair.
First you need to prepare the car for this:
- Disconnect the CM from the network.
- Shut off the water inlet valve.
- Prepare a container to collect water.
- Unscrew the inlet hose from the body and drain the water.
- Remove the manhole cover - at the bottom of the front wall.
- Prepare the container, unscrew the filter and drain the water.
- Move the SM away from the wall.
CMA Indesit, Samsung, Beko, LG, Whirpool, Ariston, Candy
The most convenient models for repair. You do not need to disassemble the washer and remove the panels. It is enough to get to the bottom of the car.
How to do it:
- Tilt the machine back to gain access to the underbody.
- Remove the bolts securing the drain pump.
- After removing the part, loosen the clamp that secures the hose to the pump.
- Disconnect the other end of the hose on the body, and pull it out.
- Install a new part with a clamp on the pump.
- Connect the other end to the chassis.
- Put the washer in place.
You coped with the task! You can deal with the connection of other communications.
СМА AEG, Siemens, Bosch
In these models, you will need to remove the front cover. Proceed sequentially:
- Pull out the dispensing tray. To do this, press the center lock and pull it towards you.
- Unscrew the screws securing the control panel.
- Release the latches around the perimeter with a flat screwdriver.
- Put the panel on top of the washer.
- Remove the bottom cover.
- Open the hatch, pull the rubber and remove the clamp.
- Insert sealing rubber into the drum.
- With your hand in the case, disconnect the hatch lock wires.
- Remove the bolts holding the front panel, remove it.
Fine! Accessed. Now decide how to remove the drain hose.
- Remove the hose clamp to the pump.
- Remember how the element is attached to the body.
- Disconnect and pull out.
- The replacement hose is installed in the reverse order. Attach immediately to the pump and then to the casing.
Check the strength of the mounts.
CMA Electrolux and Zanussi
Here you will need to remove the back panel. The process is simpler and faster than in the previous case. Get started:
- Loosen the screws as described above and lift the top cover.
- Remove the bolts located around the perimeter of the rear wall. If they are covered with caps, remove them with a flat screwdriver.
- With the panel aside, locate the pump below.
- Unclip the hose clamp with passers, disconnect it.
- Disconnect it from the case.
- Install the new part in the reverse order.
There is! You can test the car by running the wash.
Top-loading CM models
After reading our article, you will learn how to remove all the walls and panels of your washer. In vertical machines, you need to remove the side panel.
Proceed:
- Remove all screws securing the side. They can be located both on the front and on the back side.
- After you see the pump, loosen the clamp and disconnect the hose immediately from the pump, then from the body.
- Replacement is performed according to the same principle.
You can repair the drain hose of the washing machine: if the damage is small - a small crack - they can be sealed. Also check for clogging. It can be cleaned under water pressure or special means.
Now you know how to change or clean the drain element. Follow our instructions and you will succeed. Watch the related video: