There are quite a few available methods to quickly remove glue from the glass. To choose the most effective, it is necessary to clarify the composition of the glue. If it is made on a water basis (for example, PVA, stationery), you can remove the residues with warm water and ordinary detergent. If the base is different (polymers, rubbers and other hydrocarbons), wipers, ordinary gasoline, kerosene, white spirit, etc. are used.
What will be needed for processing?
To remove the glue, universal wipers are used, which can be purchased at any hardware store. However, if such a composition is not at hand, you can use simple analogues, for example:
- White Spirit;
- acetone;
- kerosene;
- petrol;
- ammonia solution (ammonia)
- solvents for paint;
- vegetable oil (composition does not matter);
- common dishwashing detergent;
- liquid soap.
In most cases, it is more convenient to remove the glue from the glass not manually, but with the help of special materials that can be found in any home. It can be:
- dense microfiber cloth;
- sponge for washing dishes;
- ordinary clean rag;
- cotton pad;
- stationery eraser;
- plastic spatula;
- brush for washing bottles.
How to remove glue: top 5 ways
Superglue or any other species can be removed literally at one point, especially if the pollution is recent. However, there are more complex cases - for them there are universal methods of removal, which are described below.
Universal wiper
If the stain is already old, it is better to purchase a special product and apply it to the surface with a napkin or cotton pad. The further sequence of actions is as follows:
- Wait a few minutes until the composition penetrates the stain of glue.
- Use a spatula with a pointed tip to remove residues or erase with an eraser.
- Wipe off the rest with a soft cloth. If necessary, secondary treatment and thoroughly rinse the surface.
White Spirit
The composition of this tool is very close to ordinary gasoline. It well dissolves glue, drying oil, fats.
Instructions for use of white spirit:
- Take a cotton pad, pour a little solvent on it.
- Disc abundantly lubricate the surface.
- They wait 15-20 minutes, if necessary, repeat the procedure again.
- Erase the glue with a soft cloth, eraser, sponge, etc. - depending on how easy it will be. In exceptional cases, you can use the blunt side of the knife blade (preferably clerical). But you need to work with it especially carefully so as not to leave scratches.
Ammonia and dishwashing liquid
In this case, they act like this:
- Take a tablespoon of ammonia and a teaspoon of any liquid dishwashing liquid.
- Mix both components to achieve uniformity.
- Apply a solution to the stain and wait about an hour.
- Remove contamination with an eraser, sponge or cloth.
- Wash off the remaining product and glue with water.
- Take 0.5 liters of water, pour in another 1 tablespoon of ammonia.
- Take a clean rag and wipe the surface with this mixture.
- It is then washed off and wiped dry with a microfiber cloth.
Vegetable oil
This is the most affordable tool that also helps to cope with simple spots of glue. Act as follows:
- Oil of any composition is applied to a cotton swab.
- With its help, wipe all surfaces stained with glue.
- Expect for an hour.
- Take a plastic spatula and scrape off the leftovers.
- If necessary, repeat the procedure again, and then rinse the glass with window cleaner and wipe it dry.
Liquid soap
For washing hands often use liquid soap. It is well suited for removing stains of glue:
- They take an ordinary bucket and pour warm water there.
- Add 1-2 tablespoons of liquid soap, mix.
- The solution is applied to the sponge and thoroughly wipe it with a brush on all sides.
- Wipe the glue stain with this brush until the remaining dirt is completely scraped off. Then rinse with the same solution and wipe.
Masking tape
If the tape has been pasted for a long time and has not yet been torn off, do not rush to remove it. First you need to thoroughly moisten its outer layer with hot water so that it flows under the surface and soaks the base. After that, glue stains can be easily removed with a normal detergent and sponge, cloth, etc.
If the tape has already been stripped off, you can use a regular stationery eraser, and as a means to apply any of the described compounds - vegetable oil, white spirit, etc.
Here are some more glue removers in such cases:
- turpentine;
- solvents R-4 and R-5.
The purchased products are used according to the instructions: they are applied to the surface for 15-30 minutes or longer, then residual dirt is removed.
Adhesive on car glass
In this case, it is better to use special wipers:
- WD-40;
- KERRY
- KUDO;
- dimexide (leaves a rather unpleasant odor that disappears for a long time), etc.
Petrol solvents are also quite suitable - in fact, gasoline and white spirit. When working, it is better to use only soft tools - a napkin, an eraser, a plastic spatula, etc. If you clean the stain with a knife, you can easily scratch the surface, and then repairing the glass will cost much more than cleaning it.
Pollution after scotch tape
If the stain is recent, you can remove it with another tape. The tape is glued to the surface and peeled off sharply. As a result, almost all residues stick to it, after which the glass is washed with water with a detergent or liquid soap. You can also use the tools described above: wiper, sunflower oil, dishwashing detergent, etc.
Hand glue removal
Do not “peel” the remnants of superglue from your hands - otherwise there is a real danger of scratching the skin and even tearing it off. Therefore, it is better to take a cotton pad and apply one of the following means with it:
- nail polish remover;
- petrolatum;
- vegetable oil;
- hand cream;
- White Spirit.
If you have water-based stationery glue on your hands, it is enough to wash your skin well with warm water and soap or a dishwashing detergent. The same method helps to remove the remains of superglue, but provided that the spots are completely fresh. The remaining stain can be carefully cleaned with a pumice stone.
5 precautions
Since glass is a potentially hazardous material that can break or be damaged, work with it especially carefully. To do this, you must follow simple safety rules:
- Removing glue and other contaminants with sharp metal objects is not allowed. They leave scratches on the surface that damage the appearance of the glass.
- Do not use abrasives for cleaning - for example, powders, metal sponges, sandpaper. The reason is the same - they leave scratches.
- It is important to understand that solvents (acetone, kerosene, gasoline, etc.) wash off glue residue well enough, but they can leave streaks. Therefore, after such processing, the glass must be thoroughly washed. If the pollution is quite large, it is better to use other means.
- It is impossible to heat glass or mirrors - it is very difficult to ensure uniform heating at home. Therefore, as a result, the glass can simply burst, flying apart into fragments throughout the room.
- Finally, if all the methods have been tried and it became obvious that the glass cannot be cleaned at home, it is better to contact a professional company. Otherwise, constant pressure on the surface can lead to scratches and even chips, so it’s better not to risk it again.
Thus, before removing the glue, it is necessary to clarify its composition. After that, you can use the product on an aqueous or organic basis - and in both cases, the work is best done without the use of abrasives and sharp objects. If the stain is too complicated, it is best to immediately contact a specialized service.